25KV Aluminum XLP MV LLDPE Jacket
Aluminum Conductor. TRXLP Insulation. Bare Copper Concentric Neutrals. Low Density Polyethylene Jacket.
Predominantly used for primary underground distribution in conduit systems suitable for use in wet or dry locations, direct burial, underground duct, and where exposed to sunlight. To be used at 25,000 volts or less and at conductor temperatures not to exceed 90°C for normal operation.
| Conductor | Ground Wire | ||||||||
| No. of Conductors | Size (AWG or kcmil) | No. of Strands | Insulation Thickness (mils) (mm) | Size (AWG) | No. of Strands | Nom. OD (mils) (mm) | Nominal Total Weight (lbs/1000') (kgs/km) | Allowable Ampacity | |
| 627871 | 1 1 | 2 AWG 2 AWG | 7 7 | 260 6.60 | 1151 29.24 | 537 800 | |||
| 115657 | 1 1 | 1 AWG 1 AWG | 19 19 | 260 6.60 | 1190 30.23 | 661 983 | |||
| 329474 | 1 1 | 1/0 AWG 1/0 AWG | 19 19 | 260 6.60 | 1220 30.99 | 735 1093 | |||
| 500447 | 1 1 | 2/0 AWG 2/0 AWG | 1 1 | 260 6.60 | 1233 31.32 | 663 986 | |||
| 347567 | 1 1 | 4/0 AWG 4/0 AWG | 19 19 | 260 6.60 | 1386 35.21 | 883 1314 | |||
| 276386 | 1 1 | 350 KCMIL 350 KCMIL | 37 37 | 260 6.60 | 1559 39.60 | 1214 1807 | |||
| 611800 | 1 1 | 500 KCMIL 500 KCMIL | 37 37 | 260 6.60 | 1774 45.07 | 1625 2419 | |||
| 613716 | 1 1 | 750 KCMIL 750 KCMIL | 61 61 | 260 6.60 | 1963 49.88 | 2160 3215 | |||
| 347302 | 1 1 | 1000 KCMIL 1000 KCMIL | 61 61 | 260 6.60 | 2184 55.49 | 2765 4115 | |||
| 320853 | 1 1 | 2 AWG 2 AWG | 7 7 | 260 6.60 | 1151 29.24 | 586 872 | |||
Southwire 25kV HI-DRI Primary UD TRXLP Cable meets or exceeds the following ASTM specifications:
The cable is composed of a reverse lay compressed stranded 1350-H16/26 aluminum phase conductor, covered by a semi-conducting cross-linked polyethylene strand shield, a tree-retardant cross-linked polyethylene primary insulation, and a semi-conducting cross-linked polyethylene insulation shield. Conductors are available with 100% insulation level. A concentric neutral of bare copper wires and a sunlight resistant, -40°C rated, insulating linear low density polyethylene jacket are applied over the insulation shield. The cable is identified by surface print on the jacket and with the lightning bolt symbol for supply cables indented in the jacket. Red extruded stripes available upon request.
