CU 600V XLPE Insulation PVC Jacket XHHW-2 With Green Ground. CT Rated - Sunlight Resistant - For Direct Burial - Silicone Free
Type TC-ER Control Cable 600Volt Copper Conductors, Cross Linked Polyethylene (XLPE) Insulation XHHW-2 Polyvinyl Chloride (PVC) Jacket with 1 Insulated Green CU Ground, Control Cable Conductor Identification Method 1 Table 2. Silicone Free
Application
Southwire’s 600 Volt Type TC-ER control cables are suited for use in wet and dry areas, conduits, ducts, troughs, trays, direct burial, aerial supported by a messenger, and where superior electrical properties are desired. These cables are capable of operating continuously at the conductor temperature not in excess of 90°C for normal operation in wet and dry locations, 130°C for emergency overload, and 250°C for short circuit conditions. For uses in Class I, II, and III, Division 2 hazardous locations per NEC Article 501 and 502. Constructions with 3 or more conductors are listed for exposed runs (TC-ER) per NEC 336.10. Silicone Free
Specifications
| Cond. Size (AWG/Kcmil) | Conductor Number | Cond. Strands | Insulation Thickness (mils) (mm) | Ground (No. x AWG) | Jacket Thickness (mils) (mm) | Approx. OD (in) (cm) | Copper Weight (lbs/1000') (kgs/km) | Approx. Weight (lbs/1000') (kgs/km) | DC Resistance @ 25C (ohms/1000') (ohms/km) | AC Resistance @ 75C (ohms/1000') (ohms/km) | Min. Bend Radius (in) (cm) | Raceway Ampacity @ 75C (amps) | Raceway Ampacity @ 90C (amps) | |
| More Options |
14
14
|
3
3
|
7
7
|
30
0.76
|
1x14
1x14
|
45
1.14
|
0.409
1.04
|
51
76
|
110
164
|
2.631
3.92
|
3.170
4.72
|
1.6
4.06
|
20
20
|
25
25
|
| More Options |
12
12
|
3
3
|
7
7
|
30
0.76
|
1x12
1x12
|
45
1.14
|
0.449
1.14
|
81
121
|
152
226
|
1.662
2.47
|
2.002
2.98
|
1.8
4.57
|
25
25
|
30
30
|
| More Options |
12
12
|
4
4
|
7
7
|
30
0.76
|
1x12
1x12
|
45
1.14
|
0.491
1.25
|
101
150
|
176
262
|
1.662
2.47
|
2.002
2.98
|
2.0
5.08
|
20
20
|
24
24
|
| More Options |
10
10
|
3
3
|
7
7
|
30
0.76
|
1x10
1x10
|
45
1.14
|
0.547
1.39
|
129
192
|
224
333
|
1.040
1.55
|
1.253
1.86
|
2.2
5.59
|
35
35
|
40
40
|
| More Options |
10
10
|
4
4
|
7
7
|
30
0.76
|
1x10
1x10
|
60
1.52
|
0.603
1.53
|
161
240
|
273
406
|
1.040
1.55
|
1.253
1.86
|
2.4
6.10
|
28
28
|
32
32
|
* Ampacities based upon 2023 NEC Table 310.16 and do not take into account the overcurrent protection limitations in NEC 240.4(D) of 15 Amps for 14 AWG CU, 20 Amps for 12 AWG CU, and 30 Amps for 10 AWG CU (independent of the conductor temperature rating and stranding if size is present in table). Also, see NEC sections 310.15 and 110.14(C) for additional requirements.
* Ampacities have been adjusted for more than Three Current-Carrying Conductors.
Standards & References
- ASTM B3 Soft or Annealed Copper Wire
- ASTM B8 Concentric-Lay-Stranded Copper Conductors
- UL 44 Thermoset-Insulated Wires and Cables
- UL 1277 Electrical Power and Control Tray Cables
- UL 1685 Vertical-Tray Fire Propagation and Smoke Release Test
- ICEA S-58-679 Control Cable Conductor Identification Method 1 Table 2
- ICEA S-73-532 Standard for Control, Thermocouple Extension and Instrumentation Cables
- ICEA S-95-658 (NEMA WC70) Power Cables Rated 2000 Volts or Less for the Distribution of Electrical Energy
- VW-1 (Vertical-Wire) Flame Test
Construction
- Conductor: 7 strands class B compressed bare copper per ASTM B3 and ASTM B8
- Insulation: Cross Linked Polyethylene (XLPE) XHHW-2, 30 Mils thick for all cable sizes
- Grounding Conductor: Class B compressed stranded copper with green insulation
- Filler: Polypropylene filler
- Overall Jacket: Polyvinyl Chloride (PVC) Jacket