SPEC 45053 CU 600V XLPE Insulation Thermoplastic CPE-TP Jacket XHHW-2. CT Rated - Sunlight Resistant - For Direct Burial - Silicone Free

Type TC-ER Control Cable 600Volt Copper Cross Linked Polyethylene (XLPE) Insulation XHHW-2 Thermoplastic Chlorinated Polyethylene (CPE-TP) Jacket, Control Cable Conductor Identification Method 1 Table 2. CT Rated - Sunlight Resistant - For Direct Burial - Silicone Free

Download Category Specifications
Excel Table

Application

Southwire’s 600 Volt Type TC-ER control cables are suited for use in wet and dry areas, conduits, ducts, troughs, trays, direct burial, aerial supported by a messenger, and where superior electrical properties are desired. These cables are capable of operating continuously at the conductor temperature not in excess of 90°C for normal operation in wet and dry locations, 130°C for emergency overload, and 250°C for short circuit conditions. For uses in Class I, II, and III, Division 2 hazardous locations per NEC Article 501 and 502. Constructions with 3 or more conductors are listed for exposed runs (TC-ER) per NEC 336.10. Sunlight Resistant - For Direct Burial - Silicone Free

Specifications

Select a set of products below for more information:
Conductor Ground Wire
No. of Conductors Size (AWG or kcmil) (mm2) No. of Strands Insulation Thickness (mils) (mm) Size (AWG) No. of Strands Nom. OD (mils) (mm) Nominal Total Weight (lbs/1000') (kgs/km) Allowable Ampacity
890674
2 2
14 AWG 14 AWG
7 7
30 0.76
355 9.03
67 100
890675
3 3
14 AWG 14 AWG
7 7
30 0.76
376 9.56
92 136
890676
4 4
14 AWG 14 AWG
7 7
30 0.76
409 10.41
111 166
890677
5 5
14 AWG 14 AWG
7 7
30 0.76
447 11.36
129 192
890678
7 7
14 AWG 14 AWG
7 7
30 0.76
486 12.35
172 256
890679
9 9
14 AWG 14 AWG
7 7
30 0.76
587 14.93
231 344
550407
12 12
14 AWG 14 AWG
7 7
30 0.76
670 17.02
299 445
550411
2 2
12 AWG 12 AWG
7 7
30 0.76
388 9.87
90 134
890681
3 3
12 AWG 12 AWG
7 7
30 0.76
412 10.46
121 180
890682
4 4
12 AWG 12 AWG
7 7
30 0.76
449 11.41
154 230
890683
5 5
12 AWG 12 AWG
7 7
30 0.76
491 12.48
179 266
890684
12 12
12 AWG 12 AWG
7 7
30 0.76
738 18.76
408 607
890685
3 3
10 AWG 10 AWG
7 7
30 0.76
463 11.77
167 249
890686
4 4
10 AWG 10 AWG
7 7
30 0.76
547 13.90
229 341
550420
5 5
10 AWG 10 AWG
7 7
30 0.76
587 14.93
270 402
550421
7 7
10 AWG 10 AWG
7 7
30 0.76
639 16.23
358 532

Standards & References

  • ASTM B3: Soft or Annealed Copper Wire
  • ASTM B8: Concentric-Lay-Stranded Copper Conductors
  • UL 44: Thermoset-Insulated Wires and Cables
  • UL 1277: Electrical Power and Control Tray Cables
  • UL 1685: FT4 Vertical-Tray Fire Propagation and Smoke Release Test
  • ICEA S-58-679: Control Cable Conductor Identification Method 1 Table 2
  • ICEA S-73-532: Standard for Control, Thermocouple Extension and Instrumentation Cables
  • ICEA S-95-658: (NEMA WC70) Power Cables Rated 2000 Volts or Less for the Distribution of Electrical Energy
  • IEEE 1202: FT4 Flame Test (70,000) BTU/hr Vertical Tray Test

Construction

  • Conductor: 7 strands class B compressed copper per ASTM B3 and ASTM B8
  • Insulation: Cross Linked Polyethylene (XLPE) XHHW-2, 30 Mils thick for all cable sizes
  • Filler: Polypropylene filler on cables with 5 or less conductors
  • Binder: Polyester flat thread binder tape applied for cables with more than 5 conductors
  • Overall Jacket: Thermoplastic Chlorinated Polyethylene (CPE-TP) Jacket

Resources

There are no downloadable resources for this product.