SPEC: 46002

CU Compressed 2.4kV NLEPR Insulation PVC Jacket. MV 90. SPEC46002

Type MV-90 Single Conductor Copper, No Lead Ethylene Propylene Rubber (NL-EPR) Polyvinyl Chloride (PVC) Jacket

Download Category Specifications

Application & Features

Southwire’s 2.4KV cables are suited for use in wet and dry areas, conduits, ducts, troughs, direct burial, and where superior electrical properties are desired. These cables are capable of operating continuously at the conductor temperature not in excess of 90°C for normal operation, 130°C for emergency overload, and 250°C for short circuit conditions. Cable can be installed in conduit without the aid of lubrication. Rated for 1000 lbs./FT maximum sidewall pressure.

Specifications

Select a set of products below for more information:

	Cond. Size	Cond. Strands	Diameter Over Conductor (in) (cm)	Diameter Over Insulation (in) (cm)	Insulation Thickness (mils) (mm)	Jacket Thickness (mils) (mm)	Approx. OD (in) (cm)	Approx. Weight (lbs/1000') (kgs/km)	Max Pull Tension (lbs) (kg)	Min. Bend Radius (in) (cm)	Conduit Size (in) (cm)
More Options	2 AWG 2 AWG	7 7	0.282 0.72	0.570 1.45	125 3.18	25 0.64	0.746 1.89	413 615	530 240.40	5.9 14.99	2.5 6.35
More Options	1 AWG 1 AWG	19 19	0.322 0.82	0.610 1.55	125 3.18	85 2.16	0.786 2.00	484 720	669 303.45	6.2 15.75	2.5 6.35
More Options	1/0 AWG 1/0 AWG	19 19	0.361 0.92	0.650 1.65	125 3.18	85 2.16	0.826 2.10	568 845	844 382.83	6.6 16.76	2.5 6.35
More Options	2/0 AWG 2/0 AWG	19 19	0.405 1.03	0.695 1.77	125 3.18	85 2.16	0.871 2.21	671 999	1064 482.62	6.9 17.53	2.5 6.35
More Options	3/0 AWG 3/0 AWG	19 19	0.456 1.16	0.745 1.89	125 3.18	105 2.67	0.955 2.43	830 1235	1342 608.72	7.6 19.30	3.0 7.62
More Options	4/0 AWG 4/0 AWG	19 19	0.512 1.30	0.785 1.99	125 3.18	105 2.67	0.995 2.53	978 1455	1692 767.48	7.9 20.07	3.0 7.62
More Options	250 KCMIL 250 KCMIL	37 37	0.558 1.42	0.870 2.21	140 3.56	120 3.05	1.112 2.82	1179 1755	2000 907.18	8.8 22.35	3.5 8.89
More Options	350 KCMIL 350 KCMIL	37 37	0.661 1.68	0.965 2.45	140 3.56	120 3.05	1.207 3.07	1531 2278	2800 1270.06	9.6 24.38	3.5 8.89
More Options	500 KCMIL 500 KCMIL	37 37	0.789 2.00	1.090 2.77	140 3.56	120 3.05	1.322 3.36	2052 3054	4000 1814.37	10.5 26.67	4.0 10.16
More Options	750 KCMIL 750 KCMIL	61 61	0.968 2.46	1.335 3.39	155 3.94	135 3.43	1.611 4.09	3038 4521	6000 2721.55	12.8 32.51	4.5 11.43
More Options	1000 KCMIL 1000 KCMIL	61 61	1.117 2.84	1.485 3.77	155 3.94	135 3.43	1.761 4.47	3893 5793	8000 3628.74	14.0 35.56	5.0 12.70

* Conduit size based on 3 phase 40% fill-factor without ground

	Cond. Size	DC Resistance at 25C (ohms/1000') (ohms/km)	AC Resistance at 75C (ohms/1000') (ohms/km)	Inductive Reactance (ohms/1000') (ohms/km)	Allowable Ampacity In Duct 90C	Allowable Ampacity In Duct 105C	Allowable Ampacity In Air 90C	Allowable Ampacity In Air 105C
More Options	2 AWG 2 AWG	0.162 0.24	0.204 0.30	0.043 0.06	145 145	- -	190 190	- -
More Options	1 AWG 1 AWG	0.128 0.19	0.162 0.24	0.042 0.06	170 170	- -	225 225	- -
More Options	1/0 AWG 1/0 AWG	0.102 0.15	0.128 0.19	0.040 0.06	195 195	- -	260 260	- -
More Options	2/0 AWG 2/0 AWG	0.081 0.12	0.102 0.15	0.039 0.06	220 220	- -	300 300	- -
More Options	3/0 AWG 3/0 AWG	0.064 0.10	0.081 0.12	0.038 0.06	250 250	- -	345 345	- -
More Options	4/0 AWG 4/0 AWG	0.051 0.08	0.065 0.10	0.037 0.05	290 290	- -	400 400	- -
More Options	250 KCMIL 250 KCMIL	0.043 0.06	0.056 0.08	0.037 0.06	320 320	- -	445 445	- -
More Options	350 KCMIL 350 KCMIL	0.031 0.05	0.041 0.06	0.036 0.05	385 385	- -	550 550	- -
More Options	500 KCMIL 500 KCMIL	0.022 0.03	0.030 0.04	0.034 0.05	470 470	- -	695 695	- -
More Options	750 KCMIL 750 KCMIL	0.014 0.02	0.023 0.03	0.033 0.05	585 585	- -	900 900	- -
More Options	1000 KCMIL 1000 KCMIL	0.011 0.02	0.019 0.03	0.032 0.05	670 670	- -	1075 1075	- -

* NEC ampacities are based on:
* For Duct: Table 315.60(C)(11) Detail 1.
* For Free Air: Table 315.60(C)(3).
* Inductive impedance is based on non-ferrous conduit with one diameter spacing center-to-center.

Size AWG	Stock Code
#2 #2	607457
500 500	601484 601484

Standards & References

ASTM B3 Soft or Annealed Copper Wire
ASTM B8 Concentric-Lay-Stranded Copper Conductors
ASTM B33 Standard Specification for Tin-Coated Soft or Annealed Copper Wire
UL 1072 Medium-Voltage Power Cables
UL 1685 Vertical-Tray Fire Propagation and Smoke Release Test
ICEA S-96-659 (NEMA WC 71) 2001-5000 V Nonshielded Cables
CT USE Sizes 1/0 AWG and Larger
Made in America: Compliant with both Buy American and Buy America Act (BAA) requirements per 49 U.S.C. § 5323(j) and the Federal Transit Administration Buy America requirements per 49 C.F.R. part 661

Construction

Conductor:Class B compressed stranded bare copper per ASTM B3 and ASTM B8 (Tinned Copper per ASTM B33 optional)
Conductor Shield:Semi-conducting cross-linked copolymer
Insulation:No Lead Ethylene Propylene Rubber (NL-EPR)
Overall Jacket:Polyvinyl Chloride (PVC)

Resources

There are no downloadable resources for this product.