500-37 CU 220 TR-XLP 24x14 CB PVC INNER JKT AIA RED PVC JACKET 15KV 133% HV TECK CSA

Southwire #: 67298299

Download Category Specifications

PDF Excel Table

Select Product Specifications

Construction

Packaging

Application & Features

Southwire's 15kV HVTECK is a CSA armoured cable for industrial and commercial medium voltage applications. Rated FT4, -40°C, Hazardous Locations (HL). These cables are capable of operating continuously at the conductor temperature not in excess of 105°C for normal operation, 140°C for emergency overload, and 250°C for short circuit conditions. Rated for 1000 lbs /FT maximum sidewall pressure. These cables feature sunlight and moisture resistance, exceptional corona resistance, resistance to most chemical soils and acids and are flame retardant.

Specifications

Cond. Size	500 KCMIL 500 KCMIL
Cond. Strands	37 37
Diameter Over Conductor (in) (cm)	0.789 2.00	inch cm
Diameter Over Insulation (in) (cm)	1.275 3.24	inch cm
Insulation Thickness (mils) (mm)	220 5.59	mils mm
Diameter Over Shield (in) (cm)	1.335 3.39	inch cm
Inner Jacket Thickness (mils) (mm)	80 2.03	mils mm
Diameter Over Armor (in) (cm)	1.973 5.01	inch cm
Drain Wire	26x14 26x14
Jacket Thickness (mils) (mm)	60 1.52	mils mm
Approx. OD (in) (cm)	2.093 5.32	inch cm
Approx. Weight (lbs/1000') (kgs/km)	3118 4640	lbs/1000' kgs/km
Max Pull Tension (lbs) (kg)	4000 1814.37	lbs kg
Min. Bend Radius (in) (cm)	25.1 63.75	inch cm

1 Comply with ICEA S-93-639 Appendix C for jacket thickness determination

Standards & References

ASTM B3 Soft or Annealed Copper Wire
ASTM B8 Concentric-Lay-Stranded Copper Conductors
CSA C22.2 No. 174 Cables in Hazardous Locations
CSA C22.2 No. 2556 & No. 0.3 Wire and Cable Test Methods
CSA C68.10 Shielded Power Cables for Commercial and Industrial Applications - 5 to 46 KV
CSA C68.3 Shielded & Concentric Neutral Power Cable - 5 to 46 kV
CSA LTGG [-40°C] - as per C68.10 - for Cold Bend and Impact rating
CSA HL - for Hazardous Locations rating
CSA SUN RES - for Sunlight Resistant rating
ICEA S-93-639 (NEMA WC 74) 5-46 KV Shielded Power Cable
ICEA T-29-520 Flame Test (210,000 BTU/Hr)
IEEE 383 Flame Test (70,000 btu)
IEEE 1202 FT4 Flame Test (70,000) BTU/hr Vertical Tray Test (1/0 and Larger)
FT1 Flame Test (1,706 BTU/Hr nominal - Vertical Wire Flame Test)
AEIC CS-8 Specification for extruded dielectric shielded power cables rated for 5 through 46KV (Qualification Test Requirements)

Construction

Conductor: Class B compressed stranded bare copper per ASTM B3 and ASTM B8
Conductor Shield: Semi-conducting cross-linked copolymer
Insulation: 220 Mils Tree Retardant Cross Linked Polyethylene 133% insulation level
Insulation Shield: Strippable semi-conducting cross-linked copolymer
Concentric Shield: Concentrically applied copper bond / shield wires. Complies with greater than the minimum requirement as per Table 44, CSA Standard C68.10 and Table 16A, Canadian Electrical Code Part 1
Neutral Separator: Mylar tape
Inner Jacket: PVC inner jacket
Armour: Aluminum Interlocked Armour (AIA)
Overall Jacket: Red Polyvinyl Chloride (PVC) Jacket

Resources

There are no downloadable resources for this product.