Bazaarvoice SAP Hybris Integration Version 2.8.2
I need to replace the small draw stud along with the 1/2 and 3/4 knockout for this set. can I order these by themselves?
Asked by: Mike S
We are happy to help! Please contact our team at 855-798-6657 for assistance with replacement.
Answered by: SW Tools
Date published: 2020-07-24
One of our kits is missing the spacer that comes with it. What is the part number so we can replace it?
Asked by: alex25
The model number is MPXD-SD.
Answered by: SW Tools
Date published: 2020-10-05
Do you guys have a repair department, we have a couple of the knock out sets that are broken
Asked by: Samamelectric
We are happy to help! Please contact our team at 855-798-6657 for further assistance.
Answered by: SW Tools
Date published: 2020-04-06
Does the punch work on Stainless Steel?
Asked by: Stainless steel
Yes it does.
Answered by: SW Tools
Date published: 2020-03-09
How to remove the draw stud from the tool head if over tightened? Any way to keep the female part from turning?
Thanks
Asked by: Frank0351
Please contact our team at 855-798-6651 for further assistance.
Answered by: SW Tools
Date published: 2020-03-09
Do you sell just the brass gear that goes on the draw stud? Ours got stripped out.
Asked by: Anonymous
Please contact our team at 855-798-6651 for further assistance.
Answered by: SW Tools
Date published: 2020-03-09
I want buy
Asked by: Raul82
Please see the link below to our Where to Buy page or call 855-798-6657 and a member of our team can help you find a distributor in your area!
http://www.southwiretools.com/tools/basic/wheretobuy
Answered by: Southwire
Date published: 2019-12-12
What is manufacturers recommended practice to remove a stuck slug inside the cup?
Asked by: JasonD
You can also use a punch or a demo screwdriver and a hammer to punch out the slug.
Answered by: Southwire
Date published: 2019-10-23
Hello, I'm looking to buy the nut driver that comes with this set separately. I believe its a 3/8 drive.
Asked by: Scott1212
Please see the link below to our Where to Buy page or call 855-798-6657 and a member of our team can help you find a distributor in your area!
http://www.southwiretools.com/tools/basic/wheretobuy
Answered by: SW Tools
Date published: 2019-08-27
need the part number for the large draw stud
Asked by: christianb
PRDS118
Answered by: Southwire
Date published: 2018-12-11
Does the 1/2"-2" set include 22.5mm and 30mm knockout punches? I am not finding anything to confirm.
Asked by: Tom Breed
Unfortunately, Southwire does not offer 22.5 and 30 mm die sets at this time.
Answered by: Southwire
Date published: 2018-11-20
Is it possable to only purchase only the part number 32886964534 This is the drill connects to.
Asked by: Wayne McKenney
Yes, please reach out to Southwire Tools Customer Service at 855-798-6657 for more information and cost.
Answered by: Southwire
Date published: 2020-02-04
do you know of anyone in the houston, Tx area that may have this in stock. Needing one asap.
Asked by: Blake
Please see the link below to our Where to Buy page or call 855-798-6657 and a member of our team can help you find a distributor in the Houston area!
http://www.southwiretools.com/tools/basic/wheretobuy
Answered by: swtools
Date published: 2018-09-06
Hi I’m lookin to get a replacement case the gray one fell apart from the rivers and corners coming undone the red one would be nice how much to purchase
Asked by: Nick pisani
Please see the link below to our Where to Buy page or call 855-798-6657 and a member of our team can help you find a distributor in your area!
http://www.southwiretools.com/tools/basic/wheretobuy
Answered by: swtools
Date published: 2018-06-13
What is the cost of this product in Canada??
Asked by: Newlevel16
Please see the link below to our Where to Buy page or call 855-798-6657 and a member of our team can help you find a distributor in your area!
http://www.southwiretools.com/tools/basic/wheretobuy
Answered by: swtools
Date published: 2018-03-23
I have a mp01 pro an apprentice has over drawn can I get the gears replaced or do I have to buy a new one?
Asked by: SparkyMtn
Please call our team at 855-798-6657 for assistance on replacing the gears.
Answered by: swtools
Date published: 2018-03-02
I have this punch and the end that you put onto the drill snapped off, is it possible to just buy a part or at least a new gear box? Thanks
Asked by: Harrison1021
Please call our Tools Team at 855-798-6657 for further assistance replacing this.
Answered by: swtools
Date published: 2019-02-19
How can I get the only the case?
I have the other case that was the grey one? Where can I get the same?
Asked by: ElectricianNY
Please see the link below to our Where to Buy page or call 855-798-6657 and a member of our team can help you find a distributor in your area!
http://www.southwiretools.com/tools/basic/wheretobuy
Answered by: swtools
Date published: 2017-11-28
does southwire have the 2-1/2" to 4" ko kit?
Asked by: kenm
We do have the 2-1/2” to 4” kit, stock number is 57177201 and model number is MP-03PRO.
Answered by: swtools
Date published: 2017-11-28
WHERE IS MAX XD MADE?
Asked by: BVedder
This product is made to our specs by an overseas manufacturer.
Answered by: swtools
Date published: 2017-09-21
How can I release the tool if the unit becomes bound-up midway through a hole punch?
Asked by: WFoster
Please contact Southwire Customer Service at 1-855-798-6657 and they will guide you with overcoming this issue and fixing your tool. Thank you.
Answered by: SouthwireTools
Date published: 2017-09-11
How much is this tool and where do I buy it?
Asked by: Russell
Hello Russell,
Please see out where to buy section here to locate a distributor in your area > http://www.southwiretools.com/tools/basic/wheretobuy. Thank you.
Answered by: SouthwireTools
Date published: 2017-08-10
Bazaarvoice SAP Hybris Integration Version 2.8.2
