SPEC: 60444

EZ-QUICK™ MCHC Health Care Facility Modular Cable Assembly

14 AWG through 10 AWG THHN/THWN Insulated Singles. Green Insulated Ground. UL Listed. 600 Volts. Rated VW-1. Lightweight Aluminum Interlocked Armor. Includes UL Listed Fittings and Prepared Cable Ends.

Download Category Specifications

Application & Features

Southwire EZ QUICK™ Health Care Facility Modular Cable Assemblies are suitable for use as follows:

Branch, feeder and service power distribution in commercial, industrial, institutional, and multi-residential buildings.

Fished or embedded in plaster.

Concealed or exposed installations.

Environmental air-handling spaces per NEC 300.22 (C).

Places of Assembly per NEC 518.4 and theaters per NEC 520.5.

Installation in cable tray and approved raceways.

Under raised floors for information technology equipment conductors and cables per NEC 645.5(D) & 645.5(D)(2)

Class I Div. 2, Class II Div 2, & Class III Div. 1 Hazardous Locations.

Southwire EZ QUICK™ Health Care Facility Modular Cable Assemblies - meets or exceeds the following requirements:

UL Online Product Guide Info - Metal-Clad Cable (PJAZ) ( www.ul.com )

Federal Specification A-A59544 (formerly J-C-30B)

NFPA 70 (National Electrical Code), Article 330

Listed for use in UL 1, 2 and 3 Hour Through Penetration Firestop Systems

REACH/RoHS-2 (Chemical Limit) Compliant

Southwire EZ QUICK™ Health Care Facility Modular Cable Assemblies Features:

Reduces installation costs up to 50% over pipe and wire.

Lightweight aluminum armor--as much as 45% lighter than steel MC Cable.

Better grounding performance than Type AC

Pre-cut lengths eliminate on-site preparation and save installation and clean up time.

Pre-stripped conductors increase jobsite safety

UL Listed snap-in fittings applied to each end

UL Classified 1, 2, and 3 hour Through Penetration Firestop Systems: W-J-3037, W-L-3110, W-L-3113, W-L-3117, W-L-3120, W-L-3121, W-L-3160, C-AJ-3115, C-AJ-3140, C-AJ-3142, C-AJ-3145, C-AJ-3173, C-AJ-3202, C-AJ-4065, C-AJ-4066, F-C-3038.

Cable reverse wound on reel for ease of pulling and installation. When pulling from coils, pull from inside to ensure ease of installation.

Anti-short bushings are not required for use with MC cable per the NEC and UL

Specifications

Select a set of products below for more information:

	Cond. Size	Conductor Number	Color
More Options	12 AWG 12 AWG	2 2	BK/WE BK/WE
More Options	12 AWG 12 AWG	4 4	BK/WE/RD/BE BK/WE/RD/BE

TBA stock codes are estimations only and actual product may vary. Please wait until a stock code is assigned to purchase connectors and/or fittings.

	Cond. Size	Conductor Number
More Options	12 AWG 12 AWG	2 2
More Options	12 AWG 12 AWG	4 4

* Ampacities based upon 2023 NEC Table 310.16. See NEC sections 310.15 and 110.14(C) for additional requirements.
* Ampacities have been adjusted for more than Three Current-Carrying Conductors.

Stock Code	Size AWG	Cond. Num	Solid/Stranded	Color	Length ft
595470	12 12	2 2	Stranded Stranded	BK, WE BK, WE	3 3
587328	12 12	2 2	Stranded Stranded	BK, WE BK, WE	5 5
595468	12 12	2 2	Stranded Stranded	BK, WE BK, WE	10 10
595469	12 12	2 2	Stranded Stranded	BK, WE BK, WE	11.6 11.6
587330	12 12	4 4	Stranded Stranded	BK, WE, RD, BE BK, WE, RD, BE	5 5
595471	12 12	4 4	Stranded Stranded	BK, WE, RD, BE BK, WE, RD, BE	5 5

Standards & References

ASTM B3 Soft or Annealed Copper Wire
ASTM B8 Concentric-Lay-Stranded Copper Conductors
UL 83 Thermoplastic Insulated Wires and Cables
UL 1569 Metal-Clad Cables
UL 1479 Standard for Safety Fire Tests of Penetration Firestops
UL 1685 FT4 Vertical-Tray Fire Propagation and Smoke Release Test
Buy American: Compliant with Buy American Requirements, found in 49 U.S.C. § 5323(j); specify “Made in the USA Only!” when ordering to ensure your project receives American made products.

Construction

Conductor:Solid or Class B compressed stranded copper per ASTM B3 and ASTM B8
Insulation:All phases are insulated with Polyvinyl Chloride with Nylon Sheath Type THHN/THWN
Ground: Green insulated copper ground with full-sized bare 8000 series aluminum grounding/bonding conductor. Armor and bare aluminum conductor form the equipment ground path
Binder:Binder tape bearing the print legend is wrapped around the cable assembly
Connector:Zinc die-cast snap on connector
Armor:Green Aluminum Interlocked Armor

Resources

There are no downloadable resources for this product.